Solid-state "relay" kits

sales@comagination.com

| Combo special | Selection by bulb | Selection by bike | Specifications | FAQ | Reviews | Other products |





Motorcycle Solid-state "Relay" Kit for Low & High beams
Click picture to enlarge
or
Horns & Accessories
Solid-state "Relay" Kit
Similar to picture above except single input control wire for your switch and output +/- wires 15 amps max - no bulb connector

Important info about headlights & relays


Advantages & Features:

  • Brighter headlight. Stock & after-market bulbs are brighter because the full battery voltage reaches the bulb.* Allows use of higher wattage bulbs without fear of overload - a fried wiring harness is expensive to replace. A must have to use with additional headlights. There are solid-state "relays" for both the high and low beams.
  • Protects switchgear. Your bike's existing light switch will now only carry milliamps to control the solid-state "relay" kit doing the heavy lifting carrying many amps. Your switchgear may last forever.
  • EZ install & very small. Plug-in kit with no wire cutting. Quick disconnect wire terminals on module for battery supply enabling easier install. Amazingly small solid-state "relay" module. See quarter.
  • All solid-state. Heavy duty solid-state module components give higher reliability and durability than older mechanical relays. Solid-state uses less power and does not cause arcing which degrades parts. Faster switching.
  • High amps. Heavy duty 15 or 15 amps rating. That's a lot of power! Requires 12 volts DC.
  • Single or dual headlights. A kit is available for H1, H3, H4, or H7 single or dual headlights. The solid-state relay is a must have when using additional headlights to avoid frying the factory wiring harness.
  • Horn or siren. Universal kit will be available for auxiliary accessories. 
  • Existing headlight modulator. Just connect your existing headlight modulator's input into the kit's output.
  • All-in-one. Different kit available with a headlight modulator and solid-state "relay" functions in one module. All-in-one description here.
  • Twelve month limited warranty.

    Note: the solid-state "relay" kit outputs will be OFF if the high and low beam kit inputs are ON (+12 VDC) at the same time.

    * This can be as much as 1.5 volts difference between factory wiring and solid-state "relay" kit. The brightness is significantly noticeable on 12 volt halogen bulbs.
SPECS: Heavy duty solid-state "relay" parts (no mechanical relays); 15 or 20 amps capacity; on resistance is almost zero ohms; high heat resistant H4 female and/or male connectors; fuse holder; ring battery terminal connectors; waterproof module.

horn/accessories & headlight solid-state "relay" kits
no mechanical relays - finally!!!

Single H4 bulb; 15 amps max; model SR20H4 H4 $157.85
Dual H4 bulbs; 15 amps max; model DR20H4 H4 x 2 $173.85
Single H7 bulb; 15 amps max; model SR20H7 H7, H3 or H1 $157.85
Dual H7 bulbs; 15 amps max; model DR20H7 H7, H3 or H1 x 2 $173.85
Horn or Accessories; 15 amps max; model HR20Kit Horn/Accessories $87.80

Disclaimer RR: If comagination employees, principals, representatives, agents, or affiliates do not themselves install the equipment manufactured by them or sold through them to a buyer, the buyer agrees to use the purchased equipment at their own risk and to hold the seller and manufacturer of said equipment not responsible for any damages or liabilities which might result from the equipment's use or misuse. User of this equipment must always check it for proper operation before operating any vehicle. The infrmxxxation is subject to change and is our best effort to be accurate. We're human so mistakes are possible. Let us know should you find an error.

Picture is representative of item and actual item may vary. E.g., male quick disconnects may be replaced by a male H4 plug.

Copyright © 2001-2004 Comagination